BETAFPV Beta65X 2S Whoop Quadcopter - Frsky

Regular Price: $149.99

Special Price $129.99

BETAFPV Beta65X 2S Whoop Quadcopter - Frsky

BULLET POINT
Beta65X start a new era of 2S whoop drones. With a big improvement in power, you could fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere.
With the high performance STM32F405 processor FC boards and tuned Betaflight Ominibus 3.5.0 firmware, everyone could fly the Beta65X drone like a racing professor.
Durable and light enough frame is customed for the Beta65X. A total weight of 26g give pilots a good balance of weight and nice punch on 2S battery.
Whole drone no soldering or tinkering necessary. Customed lightest 0802 17500KV motors with cable connectors. Just plug and play.
2pcs 1S 260mAh Lipo HV batteries are recommended in default. So pilot could also use their whoop batteries.

SPECIFICATION
Weight: 26g (without battery)
Motors: 0802 17500KV with connector
Props: 31mm 4-blades props, 1.0mm shaft hole
Camera tilt angle: 35 degree
Receiver Option: Frsky XM / FullSpeed DSMX / Futaba S-FHSS / Flysky
Batteries: 260mAh 1S Lipo HV batteries

PACKAGE
1 * Beta65X BNF 2S Whoop Quadcopter
1 * Spare 31mm 4-blades props (2CW+2CCW)
2 * 260mAh 1S Lipo HV batteries (Not for PNP version)
1 * Spare Canopy

OR
  • DESCRIPTION
  • REVIEWS
  • BETAFPV Beta65X 2S Whoop Quadcopter - Frsky

    Frsky Receiver Firmware Explanation
    BETA65X Frsky receiver is now pre-flashed in EU-LBT firmware or FCC firmware. So you can choose the 2S whoop based on the firmware of your radio controller.
    If you are not sure about what firmware you have on your radio controller.
    Please check out here on our support page.--27th Septmber 2018

    BETA65X Frsky receivers were all pre-flashed in FCC firmware before 27th September.
    Thus,if your radio controller uses EU-LBT firmware, you have to flash the firmware of the Frsky receiver to EU-LBT firmware. Otherwise, you can't bind successfully. 
    For EU-LBT firmware users that has bought Beta65X with FCC firmware for Frsky receiver, you can checkout here to find out how to flash Frsky receiver to EU-LBT firmware.

    Cli Dump & Methods to Connect the Receiver to the 2S FC & Binding Procedures
    Note: The DSMX receiver used on the 65X is different from the one we used before. The binding procedure is also different. Check out the details on the support page below.
    Find out details on our support page.

    This is a new era for Whoop drones. 2S Whoop drone has the power to fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere. Beta75X and Beta65X. X is for "eXtreme".

    BETA65X Speed Test by Daniel Sugano

    Detailed review about Beta65X by Daniel Sugano.



    A detailed review of the Beta75X drone by Nate Payne on YT.

    Another overview and flight video by  Brenden Guffin.

    For more video about these 2S Whoop drone, please check here:

    More Overview Videos

    Have any questions about 2S Whoop drone, please join our group on Facebook:

    2S POWER-WHOOP GROUP

    Join the online discussion about 2S Whoop drones at RCGroups.com:

    Beta65X   Beta75X

    The big brother Beta75X is available too. Get a Beta75X here.

    BULLET POINT

    • Beta65X start a new era of 2S whoop drones. With a big improvement in power, you could fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere.
    • With the high performance STM32F405 processor FC boards and tuned Betaflight Ominibus 3.5.0 firmware, everyone could fly the Beta65X drone like a racing professor.
    • Durable and light enough frame is customed for the Beta65X. A total weight of 26g give pilots a good balance of weight and nice punch on 2S battery.
    • Whole drone no soldering or tinkering necessary. Customed lightest 0802 17500KV motors with cable connectors. Just plug and play.
    • 2pcs 1S 260mAh Lipo HV batteries are recommended in default. So pilot could also use their whoop batteries.

    SPECIFICATION

    FC SPECIFICATIONS

    Find more details about this 2S F4 FC board  in another page.

    • CPU: STM32F405
    • Six-Axis: MPU6000
    • Size: 26mm x 26mm, whoop mounting pattern
    • Firmware version: Betaflight OMNIBUSF4SD (OBSD) 3.5.0
    • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
    • Smart Audio port is available for radio control VTX

    ESC SPECIFICATIONS

    Find more details about this 2S ESC board in another page.

    • Support BLheli/BLHELI_S suite Pass-through ready
    • Dshot600 in default
    • Input voltage: 2S lipo
    • Cotinue current: 6A
    • Peak current: 10A 
    • Firmware: BLHELI_S
    • Processor: SILABS EFM8BB21F16G

    Z02 AIO Camera VTX

    Find more details about this AIO Z02 camera VTX in another page. On the Beta65X, it is the customed version with VTX board and camera board split.

    • Output power: 0mW, 25mW and 200mW (Adjustable)
    • Smart Audio function is included for radio control
    • Antenna: Dipole ANT
    • Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
    • TV System: NTSC
    • Field of view: 100-120 degrees with 1/4 lens

    PROPS OUT

    The Beta65X drone also comes with "props out" in default. Why we need "props out" direction?

    Default Betaflight props direction, quadcopter dips and "washes out" in hard corners. With reversed props or "props out", no more dipping even in hardest cornering.

    Know more about "Props Out".

    POWER CABLE

    There is only one choices for the Beta65X battery -- PH 2.0 option for you. The two 260mAh Lipo HV 1S batteries can be inserted into the slot in design, as seen below.

    CUSTOMED Z02

    The AIO camera VTX on the Beta665X is a customed version of Z02. The VTX board and camera board are split and 35 degree camera mount for more fast flying. At the same time, it have all the other function of the Z02 camera, like output power switchable between 0mW, 25mW and 200mW. Smart audio is available for VTX remote control in default.

    How to change the frequncy or output power via remont control, please check the manual Smart Audio.

    Download the STL file for the camera mount.

    FAQ

    1. About the LED at the rear for Beta65X

    For the moment, the FC board doesn't support programable LED like WS2812 etc. The LED holder is designed on the frame nowadays. So we will update the FC board on the next version and release the suitable LED board.

    Note: there is NO rear LED holder for Beta65X in default.

    2. I am interested in connecting an HD camera and DVR, but I don't want to overload the circuit of 5V.

    The 5V regulator on the FC board could handle 2A of load. So you could use it for HD camera or DVR board. More details, please check the FC board page.

    3. Does this drone have current sensor?

    This drone does NOT have a real current sensor. We use the virtual current meter in Betaflight. When properly calibrated, it can be accurate enough to be useful. Here is the pre-calibrated value out of the box.

    set current_meter = VIRTUAL
    set ibatv_scale = 90
    set ibatv_offset = 29

    4. How to connect the receiver to the 2S brushless FC?

    Please don't forget to plug the battery when you try to connect the connector to the 2S brushless FC. Find out more details in our support page.

    5. Cli Dump for different versions of the 2S Whoop are provided in our support page.

    PACKAGE

    • 1 * Beta65X BNF 2S Whoop Quadcopter
    • 1 * Spare 31mm 4-blades props (2CW+2CCW)
    • 2 * 260mAh 1S Lipo HV batteries (Not for PNP version)
    • 1 * Spare Canopy

  • Write A Review For BETAFPV Beta65X 2S Whoop Quadcopter - Frsky

    How do you rate this product? *

    • Price
    • Value
    • Quality