GnarlyFPV Primo 3 3K Carbon Frame

$21.49

Included:
Primo 3 UltralightPlus Carbon frame
Liteweight battery strap
Liteweight battery pad
P3 Jelly Mount
Axii Micro / Whip compatible canopy
Set of zip ties (To secure motor leads, and optional Whip antenna to canopy)
Hardware
Forever Tubes
HQ T3x2 props (Smoke)
Canopy and Jelly Mount Color: Teal

Specs:
Thickness: 2.5mm chamfered 3K carbon
Mounting pattern: 6.6mm 3 hole / 9mm "4" hole hybrid motor mount layout. Supports the following known motors. 060X/070X/080X/090X/110X
Large E clip motor adapter set
Liteweight battery strap (View photos for battery strap layout) designed for sideways battery mounting "Toilet Tank".
Preinstalled liteweight battery pad
Forever tubes to keep your RX antennas in check.
AUW: 15 grams Dry (With included battery strap and forever tubes)
Highly effecient HQ T3x2 bi-blade props
Highly durable canopy. Supporting the latest nano camera options available. Runcam Racer Nano, Runcam Nano 2, Caddx EOS2. All cameras are a direct fit. No camera adapters required.

OR
  • DESCRIPTION
  • REVIEWS
  • Finally! The Primo 3 has arrived!

    The Primo 3 is the 3 inch evolution of the original Primo. Spinning the new HQ T3x2 props, the power to efficiency ratio is brilliant. Top that off with a stout 2.5mm unibody frame, a light weight battery strap and battery pad for sideway battery mounting! This may very well be the perfect UltralitePlus frame for that Track or Bando rip.

     

     

    Included:

    • Primo 3 UltralightPlus Carbon frame
    • Liteweight battery strap
    • Liteweight battery pad
    • P3 Jelly Mount
    • Axii Micro / Whip compatible canopy
    • Set of zip ties (To secure motor leads, and optional Whip antenna to canopy)
    • Hardware
    • Forever Tubes 
    • HQ T3x2 props (Smoke)
    • Canopy and Jelly Mount Color: Teal 

     

    Specs: 

    • Thickness: 2.5mm chamfered 3K carbon
    • Mounting pattern: 6.6mm 3 hole / 9mm "4" hole hybrid motor mount layout. Supports the following known motors. 060X/070X/080X/090X/110X 
    • Large E clip motor adapter set
    • Liteweight battery strap (View photos for battery strap layout) designed for sideways battery mounting "Toilet Tank".
    • Preinstalled liteweight battery pad
    • Forever tubes to keep your RX antennas in check.
    • AUW: 15 grams Dry (With included battery strap and forever tubes)
    • Highly effecient HQ T3x2 bi-blade props
    • Highly durable canopy. Supporting the latest nano camera options available. Runcam Racer Nano, Runcam Nano 2, Caddx EOS2. All cameras are a direct fit. No camera adapters required. 

    Recommended electronics:

    • Gep 12A F4 Flight Controller downward facing USB 
    • BetaFPV 12A Flight Controller downward facing USB 
    • NamelessRC Flight Controller downward facing USB
    • 1103 (Power/effecient)
    • 1104/1105/1106(POWA)
    • Power switchable micro VTX 
    • RunCam Nano 2 / Racer Nano / EOS2
    • Frsky R-XSR
    • Frsky XM
    • Dsmx or Flysky Nano sized receivers
    • Motor lead extensions available on site for motors with short leads or with no connectors

    NOTE:

    Due to the rising popularity of the 1103 and larger micro motors class, we have recently become aware that some manufacturers have decided to use larger then "standard" E clips on the most recently released motors. These larger E clips can rub against the frame and cause binding, or the inability to mount the motors properly at all. To help remedy this, we have designed a simple yet effective motor adapter. This included adapter will mount between the frame and the motor, raising the motor up to avoiding any binding. This issue is only caused by a few new motors from Xing in the 110X class. 

     

    Primo's were designed to be built with Light/Small RX/VTX components. We did this to keep the weight and profile down as much as possible. This will give you a GREAT flying experience! Below we have compiled a small list of small RX and VTX components that we recommend for the build. No spacers needed if you keep your gear small. :D

     

    RX:

    • XM
    • RXSR (Plug removed)
    • Fullspeed Nano ( Frsky, Dsmx, Flysky)
    • Crazybee F4 V2.0/3.0 (Built in RX)

    VTX:

    • Eachine Nano VTX
    • TBS Nano
    • iflight Whoop vtx ( FC/Whoop Combo stack)
    • Happymodel Whoop VTX ( With our spacer or one of similar slim profile ) Some spacer are too thick and raise the VTX higher then needed. 
    • AIO Camera VTX 

     

     

    Please note that the Primo 3 is an evolution of the original Primo. They are not fully cross compatible. So replacement parts and color packs will be available for the Primo 3 soon.