Heli-Nation Brand

1 - 16 of 31

Page:
  1. 1
  2. 2
  • Heli-Nation Talon F4 20x20 FC Flight Controller

    Regular Price:

    $29.99

    Heli-Nation Talon F4 20x20 FC


    When it comes to the 20x20 board, most pilot's are going to use a 4 in 1 ESC.  The problem with the 4 in 1 ESC is the connectors are not all the same. Different manufacturing has different 4 in 1 sockets, or you have to use their own flight controller to pair with their ESC.  We went ahead and designed a 20X20 board with the features people want, but also with the ability to use any 4 in 1 ESC they want. That's why we put a 4 in 1 ESC socket on the board and also added direct solder pads. With the direct solder pads for motor outputs and vbat input, this flight controller will be able to use any 20X20 ESC on the market.

    Direct 2-6S input.

    mpu6000 gyro

    Filtered 2A 5V. 

    Direct stack on xm+ rx 

    Build – betaflight OSD.

    4 in 1 ESC socket and direct solder on 4 in 1 ESC pads.

    Build in Camera control resistor and capacitor

    Anchor USB port, for more secure and durable

    Filtered 5V for camera, Vbat battery for VTX.

    Current sensor input from 4 IN 1 esc socket and Solder pad

    Inverter for Sbus (UART1)

    Inverter for smartport telemetry (UART3)

    TX4 near VTX pads for easy smart audio or tramp wiring (UART4)

    TX6(UART6 ) and RX4 ( UART4 ) 

    Includes
    1 esc cable
    8 grommets
    M3-M2 nut adapter
    M3X5 stand off x4

  • Armattan Chameleon 5" PNP

    Regular Price:

    $449.00

    Built for Heli-Nation by Candy Quads, this PNP Armattan Chameleon is ready for some Freestyle action! Built with TBS Mr. Steele motors, Spedix 30A 32 bit ESC's, Betaflight F4 flight controller, and a TBS Unify Pro HV no shortcuts were taken in these builds! Add your own receiver and you're ready to fly!

    Out of stock

  • Whitenoise RipLite Heli-Nation Team Edition PNP

    Regular Price: $399.00

    Special Price $375.00

    Fly what Team Heli-Nation races! Just add a receiver and it's ready to fly! The full build minus props and antenna is only 262 grams!

    Out of stock

  • Heli-Nation Apex 1 Replacement Motor Stator

    Regular Price:

    $9.99

    Replacement Stator for Heli-Nation Apex 1 Motor

  • Heli-Nation Apex 1 Motor Titanium Replacement Shaft

    Regular Price:

    $4.99

    Replacement Titanium Shaft for Heli-Nation Apex 1 Motor 

  • Heli-Nation Apex 1 EZO Bearing Replacement

    Regular Price:

    $5.99

    EZO Bearing Replacement Heli-Nation Apex 1 Motor

  • Heli-Nation Apex 1 Replacement Rotor Bell

    Regular Price:

    $7.99

    Replacement Rotor Bell for the Heli-Nation Apex 1 Motor

  • Whitenoise RipLite 5" Racing Frame

    Regular Price:

    $49.99

    Whitenoise RipLite 5" Racing Frame

    5mm thick beveled arms
    75 gram
    Team build 265 grams without props and battery
    Built for use with the Asgard AIO and micro camera
    Team Build

    Whitenoise RipLite 5" Racing Frame

    Heli-Nation Apex 1 Motors
    https://www.heli-nation.com/heli-nation-apex-1-team-motors-x-4-2206-2525kv-combo

    Airbot Asgard AIO F4
    https://www.heli-nation.com/preorder-airbot-asgard-v2-aio-f4-flight-controller-w-4-pcs-blheli-s-esc-on-one-pcb

    5V Unify Mounting Board
    https://www.heli-nation.com/whitenoise-fpv-unify-pro-mounting-board-pro-v2-5v-only-version

    Team Blacksheep Unify Pro 5V V2 sma Video Transmitter
    https://www.heli-nation.com/team-blacksheep-tbs-unify-pro-5g8-v2-sma-video-transmitter-rx-tx

    Foxeer or Runcam Micro Camera
    https://www.heli-nation.com/foxeer-arrow-micro-600tvl-150-degree-13-had-ii-ccd-fpv-camera-with-upgraded-osd-55g-orange
    https://www.heli-nation.com/runcam-micro-swift-2-fov-145-23mm-lens-ccd-fpv-camera-for-drone-quad-orange

    Rakon CNC AL XT60 Connector Mount Set Sky-Hero Anakin BLACK XT60CM-K
    https://www.heli-nation.com/rakon-cnc-al-xt60-connector-mount-set-sky-hero-anakin-black-xt60cm-k

    Receiver and props of choice!

  • Whitenoise Heli-Nation Team Edition RipLite 5" Racing Frame

    Regular Price:

    $49.99

    Whitenoise Heli-Nation Team Edition RipLite 5" Racing Frame

    5mm thick beveled arms
    75 gram
    Team build 265 grams without props and battery
    Built for use with the Asgard AIO and micro camera
    Team Build

    Whitenoise Heli-Nation Team Edition RipLite 5" Racing Frame

    Heli-Nation Apex 1 Motors
    https://www.heli-nation.com/heli-nation-apex-1-team-motors-x-4-2206-2525kv-combo

    Airbot Asgard AIO F4
    https://www.heli-nation.com/preorder-airbot-asgard-v2-aio-f4-flight-controller-w-4-pcs-blheli-s-esc-on-one-pcb

    Whitenoise 5V Unify Mounting Board
    https://www.heli-nation.com/whitenoise-fpv-unify-pro-mounting-board-pro-v2-5v-only-version

    Team Blacksheep Unify Pro 5V V2 sma Video Transmitter
    https://www.heli-nation.com/team-blacksheep-tbs-unify-pro-5g8-v2-sma-video-transmitter-rx-tx

    Foxeer or Runcam Micro Camera
    https://www.heli-nation.com/foxeer-arrow-micro-600tvl-150-degree-13-had-ii-ccd-fpv-camera-with-upgraded-osd-55g-orange
    https://www.heli-nation.com/runcam-micro-swift-2-fov-145-23mm-lens-ccd-fpv-camera-for-drone-quad-orange

    Rakon XT60 Connector
    https://www.heli-nation.com/rakon-cnc-al-xt60-connector-mount-set-sky-hero-anakin-black-xt60cm-k
    Receiver and props of choice!

  • WhiteNoise FPV Matek VTX-HV XM+ Mounting Board - RED

    Regular Price:

    $2.95

    You guys asked so we delivered!  Here's a mounting board for an FrSky XM+ (or really any other small receiver) that will fit nicely with the Matek VTX-HV stackable VTX.  With this board, you won't have to use any more zipties or tape to secure your receiver inside your quad.  

     

    This is only a mounting board.  There is no voltage regulator

  • Apex 1 Heli-Nation Team Motors x 4 2206 2525kv Combo

    Regular Price: $94.99

    Special Price $79.99

    Heli-Nation Apex 1 Team Motors x 4 2206 2525kv Combo

    Configuration: 12N14P
    No.of Cells(Lipo): 3-5S
    Rotor: N52H arc magnets
    Wire AWG: 20AWG
    Shaft: Titanium Alloy hollow shaft
    Stator: 0.15mm Kawasaki silicon steel
    Bearings: EZO 4 x 9 x 4mm
    Base casing: Al 7075
    Bell cap: Al 7075
    Weight:28.5g without wire

  • Apex 1 Heli-Nation Team Motor 2206 2525kv

    Regular Price: $24.99

    Special Price $20.99

    Heli-Nation Apex 1 Team Motor 2206 2525kv

    Configuration: 12N14P
    No.of Cells(Lipo): 3-5S
    Rotor: N52H arc magnets
    Wire AWG: 20AWG
    Shaft: Titanium Alloy hollow shaft
    Stator: 0.15mm Kawasaki silicon steel
    Bearings: EZO 4 x 9 x 4mm
    Base casing: Al 7075
    Bell cap: Al 7075
    Weight:28.5g without wire

  • WhiteNoise FPV TBS Unify Pro Mounting Board - RACE/HV Version - YELLOW

    Regular Price:

    $6.00

    WhiteNoise FPV TBS Unify Pro Mounting Board - RACE/HV Version - WHITE

    Allows a Team BlackSheep Unify Pro and FrSky D4R or X4R-SB to be mounted on a board for a low profile and clean stacking solution. The pads around the Unify are meant to hard mount the video transmitter to the board. Once the Unify is mounted, you can either use the plug that comes with the Unify or directly solder the wires to the pads. The button extension can also be used with this by connecting one of the pads of the button to the board. From there, you can use the button extension with the Riptide LED Back Plate.

    The FrSky receivers do not have to be used with this board. Spektrum, Futaba, etc receivers can work. You can connect the receiver directly to the flight controller (ignore the receiver portion on the board) or connect the receiver to one of the header pins on the Unify Mounting Board and use the pads as intended. The solder bridge pads will still have to be used to select which headers you will be using.

    For:

    TBS Unify Pro Video Transmitters
    FrSky D4R-II, X4R-SB
    Can also work with Spektrum, Futaba, or any other receiver

    Out of stock

  • WhiteNoise FPV TBS Unify Pro Mounting Board - RACE/HV Version - WHITE

    Regular Price:

    $6.00
    5 1

    WhiteNoise FPV TBS Unify Pro Mounting Board - RACE/HV Version - WHITE

    Allows a Team BlackSheep Unify Pro and FrSky D4R or X4R-SB to be mounted on a board for a low profile and clean stacking solution. The pads around the Unify are meant to hard mount the video transmitter to the board. Once the Unify is mounted, you can either use the plug that comes with the Unify or directly solder the wires to the pads. The button extension can also be used with this by connecting one of the pads of the button to the board. From there, you can use the button extension with the Riptide LED Back Plate.

    The FrSky receivers do not have to be used with this board. Spektrum, Futaba, etc receivers can work. You can connect the receiver directly to the flight controller (ignore the receiver portion on the board) or connect the receiver to one of the header pins on the Unify Mounting Board and use the pads as intended. The solder bridge pads will still have to be used to select which headers you will be using.

    For:

    TBS Unify Pro Video Transmitters
    FrSky D4R-II, X4R-SB
    Can also work with Spektrum, Futaba, or any other receiver

    Out of stock

  • WhiteNoise FPV TBS Unify Pro Mounting Board - V2 Version - YELLOW

    Regular Price:

    $6.00

    WhiteNoise FPV TBS Unify Pro Mounting Board - V2 Version - YELLOW

    Allows a Team BlackSheep Unify Pro and FrSky D4R or X4R-SB to be mounted on a board for a low profile and clean stacking solution. The pads around the Unify are meant to hard mount the video transmitter to the board. Once the Unify is mounted, you can either use the plug that comes with the Unify or directly solder the wires to the pads. The button extension can also be used with this by connecting one of the pads of the button to the board. From there, you can use the button extension with the Riptide LED Back Plate.

    The FrSky receivers do not have to be used with this board. Spektrum, Futaba, etc receivers can work. You can connect the receiver directly to the flight controller (ignore the receiver portion on the board) or connect the receiver to one of the header pins on the Unify Mounting Board and use the pads as intended. The solder bridge pads will still have to be used to select which headers you will be using.

    For:

    TBS Unify Pro Video Transmitters
    FrSky D4R-II, X4R-SB
    Can also work with Spektrum, Futaba, or any other receiver

  • WhiteNoise FPV TBS Unify Pro Mounting Board - V2 Version - WHITE

    Regular Price:

    $6.00

    WhiteNoise FPV TBS Unify Pro Mounting Board - V2 Version - WHITE

    Allows a Team BlackSheep Unify Pro and FrSky D4R or X4R-SB to be mounted on a board for a low profile and clean stacking solution. The pads around the Unify are meant to hard mount the video transmitter to the board. Once the Unify is mounted, you can either use the plug that comes with the Unify or directly solder the wires to the pads. The button extension can also be used with this by connecting one of the pads of the button to the board. From there, you can use the button extension with the Riptide LED Back Plate.

    The FrSky receivers do not have to be used with this board. Spektrum, Futaba, etc receivers can work. You can connect the receiver directly to the flight controller (ignore the receiver portion on the board) or connect the receiver to one of the header pins on the Unify Mounting Board and use the pads as intended. The solder bridge pads will still have to be used to select which headers you will be using.

    For:

    TBS Unify Pro Video Transmitters
    FrSky D4R-II, X4R-SB
    Can also work with Spektrum, Futaba, or any other receiver

1 - 16 of 31

Page:
  1. 1
  2. 2