Matek

Filters
Brand
  1. Matek (28)
  2. Heli-Nation (1)

1 - 16 of 29

Page:
  1. 1
  2. 2
  • MATEKSYS F405-CTR Flight Controller - STM32F405, BFOSD, Barometer, PDB, BEC 5V/2A, 184A Current Sensor

    Regular Price:

    $39.99

    MATEKSYS F405-CTR Flight Controller - STM32F405, BFOSD, Barometer, PDB, BEC 5V/2A, 184A Current Sensor

    FC Specifications
    MCU: 168MHz STM32F405
    IMU: MPU6000 accelerometer/gyro (SPI)
    Baro: BMP280 (I2C)
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: MicroSD card slot (SD/SDHC)
    VCP, UART1, UART2, UART3, UART4, UART5
    Built in inverter for SBUS input (UART2-RX)
    PPM/UART Shared: UART2-RX
    SoftSerial on TX2, S5 or S6 optional
    Camera control on S6 or DAC optional
    Smartaudio & Tramp VTX protocol supported
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes

    PDB Specifications
    Input: 6~30V (3~6S LiPo) w/TVS protection
    PDB: 4x30A (Max.4x46A), 6 layers*2oz copper PCB
    BEC: 5V 2A cont. (Max.3A)
    LDO 3.3V: Max.300mA for Spektrum RX
    Current Sensor 184A (Scale 179)
    Battery Voltage Sensor: 1:10 (Scale 110)
    3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
    6x PWM / DShot outputs without conflict
    5x UARTs
    1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
    4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
    1x pair I2C1 pads
    1x Side-press button for BOOT(DFU) mode
    36x46mm PCB with 30.5mm mounting holes
    10g
    w/ 1x Rubycon ZLH 35V/470uF (Low ESR)
    w/ 6x silicon grommets M4 to M3
    w/ 1x FR4 PCB Plate 36*36*1mm

    BF FW & Wiring
    http://www.mateksys.com/?portfolio=f405-ctr#tab-id-3

    BF Pins Definitions
    http://www.mateksys.com/?portfolio=f405-ctr#tab-id-4

    INAV FW & Wiring
    http://www.mateksys.com/?portfolio=f405-ctr#tab-id-5

    INAV Pins Definition
    http://www.mateksys.com/?portfolio=f405-ctr#tab-id-6

    Firmwares & Downloads
    http://www.mateksys.com/?portfolio=f405-ctr#tab-id-7

    Tips
    http://www.mateksys.com/?portfolio=f405-ctr#tab-id-8

  • MATEKSYS F405-STD Flight Controller - STM32F405, BFOSD, Barometer

    Regular Price:

    $30.99

    MATEKSYS F405-STD Flight Controller - STM32F405, BFOSD, Barometer

    Spec. & Features:
    MCU: 168MHz STM32F405RGT6
    IMU: 32K ICM20602 gyro/accelerometer (SPI)
    Baro: BMP280 (I2C)
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: MicroSD card slot (SD/SDHC)
    VCP, UART1, UART2, UART3, UART4, UART5
    Built in inverter for SBUS input (UART2-RX)
    PPM/UART Shared: UART2-RX
    SoftSerial on TX2, S5 or S6 optional
    Camera control on S6 or DAC optional
    Smartaudio & Tramp VTX protocol supported
    Battery Voltage Sensor: 1:10
    Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
    BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
    LDO 3.3V: Max.300mA
    I2C1 SDA & SCL: Yes
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes
    3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
    6x PWM / DShot outputs without conflict
    2x 2812LED outputs option
    5x UARTs
    1x Group of 5V/G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
    4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
    1x pair I2C1 pads
    1x Side-press button for BOOT(DFU) mode
    1x 16pin bottom mounted FFC Slot for FCHUB-6S, FCHUB-VTX or FCHUB-W connection
    36x36mm PCB with 30.5mm mounting holes
    w/ 2x 0.5mm*16Pin 5cm Flexible Flat Cable
    w/ 4pcs M3 Anti-vibration Standoffs

    BF FW & Wiring
    http://www.mateksys.com/?portfolio=f405-std#tab-id-3

    BF Pins Definitions
    http://www.mateksys.com/?portfolio=f405-std#tab-id-4

    INAV FW & Wiring
    http://www.mateksys.com/?portfolio=f405-std#tab-id-5

    INAV Pins Definition
    http://www.mateksys.com/?portfolio=f405-std#tab-id-6

    Firmwares & Downloads
    http://www.mateksys.com/?portfolio=f405-std#tab-id-7

    Tips
    http://www.mateksys.com/?portfolio=f405-std#tab-id-8

  • MATEKSYS FCHUB-W PDB for Fixed Wings - 4x BEC & 104A Current Sensor

    Regular Price:

    $14.99

    Matek Systems FCHUB-W PDB for Fixed Wings - 4x BEC & 104A Current Sensor

    Spec. & Features:

    PDB
    Input voltage range: 9~30V (3~6S LiPo) w/TVS protection
    2x ESC power pads
    Current Senor: 104A, 3.3V ADC, Scale 317
    4x BEC on board
    3x LED indicators for 5V, 10V & Vx

    Soldering Holes & Pads
    + & – : Bettery & ESC power pads
    Curr: Current sensor output
    Vbat: Bettery voltage
    G: Ground
    3V3: LDO 3.3V
    5V: BEC 5V
    10V: BEC 10V
    Vx: BEC 5V/6V/7.2V ADJ

    FFC connection
    Compatible with MATEKSYS FC F405-STD, F722-STD, F405-OSD
    MT1: Motor1 of INAV Flying Wing & Airplane
    MT2: Motor2 of INAV Flying Wing & Airplane
    SV3~SV6: Servo 3~6 of INAV Flying Wing & Airplane
    VTX: Video Transmitter signal
    TX5 & RX5: UART5 of F405-STD/F722-STD/F405-OSD

    BEC 5V output
    Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, GPS module

    BEC 10V output
    Designed for Video Transmitter, Gimble

    BEC Vx output
    Designed for Servos

    BEC 3.3V output
    Designed for Baro / Compass module and Spektrum RX

    Physical
    Mounting: 30.5 x 30.5mm, Φ3mm
    Dimensions: 52 x 36 x 6 mm
    Weight: 13g

    Connection Guide (INAV):

    http://www.mateksys.com/?portfolio=fchub-w#tab-id-3

  • Matek Systems FCHUB-A w/ Current Sensor 120A & 200A Range, No BEC

    Regular Price:

    $5.99
    Matek Systems FCHUB-A w/ Current Sensor 120A & 200A Range, No BEC

    Current Sensor 120A default, Scale is 275
    Bridge 200A pad to get 200a range, Scale is 165

    Screws M3*11, 6pcs
    Nylon Nuts M3, 6pcs

  • Matek System 20x20mm F411-mini Mini F4 Flight Controller AIO OSD BEC and LED Strip

    Regular Price:

    $24.99

    Specification:
    Brand Name: Matek
    Item Name: 20x20mm Mini F4 Flight Controller AIO OSD BEC and LED Strip
    MCU: 100MHz STM32F411
    IMU: MPU6000
    OSD: BetaFlight OSD w/ AT7456E chip
    Camera control supported on Rssi pad
    Battery Voltage Sensor: 1:10
    Current Sensor: No (FCHUB-A option)
    BEC: 5V 2A
    LDO 3.3V: Max.300mA
    I2C1 SDA & SCL available
    WS2812 Led Strip : Yes
    Built in inverter for SBUS input (UART1-RX)
    PPM/UART Shared: UART2-RX
    SoftSerial supported on S5 & S6
    Beeper : Yes
    RSSI: No
    Blackbox: No
    Size: 28x28mm
    Mounting Hole: 20x20mm
    Weight: 4.5g

    Features:
    - 20x20mm Mounting hole, only 4.5g
    - with betaflight OSD and 5V BEC output
    - with 2 LED indicator, blue and red
    - Built in inverter for SBUS input (UART1-RX)
    - PPM/UART Shared: UART2-RX

    Package Included:
    1x F4 Flight Controller
    6x Silicon grommets M4 to M3
    6x Brass grommets M3 to M2

  • Matek Systems F722-STD STM32F722 Flight Controller Built-in BetaFlight OSD BMP280 Barometer Blackbox

    Regular Price:

    $39.99

    Specification(User manual): http://www.mateksys.com/?portfolio=f722-std
    Brand name: Matek Systems
    Item name: F722-STD flight controller
    36x36mm PCB with 30.5mm mounting holes
    Weight: 7g
    MCU: 216MHz STM32F722RET6
    IMU: 32K ICM20602 gyro/accelerometer (SPI)
    Baro: BMP280 (I2C)
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: MicroSD card slot (SD/SDHC)
    VCP, UART1, UART2, UART3, UART4, UART5
    PPM/UART Shared: UART2-RX
    Battery Voltage Sensor: 1:10
    Current Sensor: No (FCHUB-6S, FCHUB-VTX option)
    BEC 5V: No (FCHUB-6S, FCHUB-VTX option)
    LDO 3.3V: Max.300mA
    I2C1 SDA & SCL: Yes
    Camera control: Yes
    DAC: Yes
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes

    Features:
    3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
    7x PWM / DShot outputs without conflict
    5x UARTs
    1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
    1x I2C1
    4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
    1x Side-press button for BOOT(DFU) mode
    1x 16pin bottom mounted FFC Slot for FCHUB-6S or FCHUB-VTX connection

    Package included:
    1x F722-STD flight controller
    2x 0.5mm*16Pin 5cm Flexible Flat Cable
    4x M3 Anti-vibration Standoffs

  • Matek Systems FCHUB-VTX 6~27V PDB 5V/1A BEC w/ 5.8G 40CH 25/200/500mW Switchable Video Transmitter

    Regular Price:

    $34.99

    Specification (user manual):http://www.mateksys.com/?portfolio=fchub-vtx
    Brand name: Matek Systems
    Item name: FCHUB-VTX
    Weight: 14g (w/ MMCX whip antenna)
    Size: 36*45*7mm w/30.5mm mounting

    Input voltage: 6~27V(2~6S LiPo)
    PDB: 4*30A (4*46A, 5 seconds)
    Current Sensor: 184A (Scale 179)
    BEC Output: 5V/1A for Camera or FC

    VTX: 40 standard 5.8G channels, A/B/E/F/R Band
    VTX Output Power: 25, 200, 500mW switchable
    Traditional button+LED control of frequency and power
    BFCMS (BFOSD & LUA Script) control via FC UART _TX
    Video signal & TX5 are ready on FFC connected with MATEK FC F405-OSD
    Silicon wires connection with other brands FC
    Firmware upgradeable

    VTX Power Consumption: 3.1W Max. @ 500mW
    Video Input Impedance: 75 Ohm
    Audio Subcarrier Frequency: 6.5 MHz
    RF Connector: MMCX
    Video Format: NTSC/PAL

    Pacakge included:
    1* FCHUB-VTX board
    1* MMCX to SMA Female, RG178 cable 9cm
    1* MMCX 5.8G whip antenna, RG178 8cm
    1* Rubycon ZLH 35V/470uF Low ESR capacitor

    Out of stock

  • Matek Systems FCHUB A5 PDB Built-in 184A Current Sensor 5V 2A BEC 2-6S

    Regular Price:

    $7.99

    Description:
    Brand name: Matek Systems
    Item name: FCHUB A5
    Input: 6-27V (2-6S Lipo)
    Input TVS protection
    PDB: 4x35A (Max. 4x46A)
    BEC: 5V 2A (Max. 2.5A)
    Current sensor: 184A
    Current scale: 179
    BLHeli32 ESC telemetry pads
    Weight: 8g
    Size: 46x36x4mm
    Mounting holes: 30.5mm & 20mmφ3mm
    Ribbon cable connection with FC F405-mini

    Package included:
    1 x FCHUB A5
    6 x screws M3*11
    6 x nylon nuts M3

  • Matek Systems F4 F405 Mini Flight Controller Integrated OSD 32K Gyro 32M Flash 20x20mm

    Regular Price:

    $28.99

    Description:
    Brand name: Matek Systems
    Item name: F405 Mini Flight Controller
    MCU: 168MHz STM32F405
    IMU: 32K ICM20602 accelerometer/gyro (SPI)
    Support 32K Gyro update & 16K PID Loop
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: 32M(256) Flash
    VCP, UART1, UART2, UART3, UART4, UART5
    Built in inverter for SBUS input (UART2-RX)
    PPM/UART Shared: UART2-RX
    SoftSerial & Camera control supported on S5 & S6
    Battery Voltage Sensor: 1:10
    Current Sensor: No (FCHUB-A5 option)
    BEC 5V: No (FCHUB-A5 option)
    LDO 3.3V: Max.300mA for Spektrum RX
    I2C1 SDA & SCL available
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes
    2x LEDs for FC STATUS (Blue, Red)
    6x PWM / DShot outputs without conflict
    5x UARTs
    1x 14pin top mounted FFC Slot for FCHUB-A5 connection
    28x28mm PCB with 20mm mounting holes
    w/ 6x silicon grommets M4 to M3
    w/ 6x brass grommets M3 to M2
    w/ 2x 0.5mm*14Pin 3cm Flexible Flat Cable
    MatekF405 Target
    Firmware based on OpenSource BetaFlight

    Package included:
    1 x F405 Mini Flight Controller
    6 x Silicon grommets M4 to M3
    6 x Brass grommets M3 to M2
    2 x FFC 0.5mm * 14 pin 30mm

  • Matek 5.8G 38CH 25/200/500mW switchable Video Transmitter VTX-HV with 5V/1A BEC Output

    Regular Price:

    $30.00
    5 1

    Matek 5.8G 38CH 25/200/500mW switchable Video Transmitter VTX-HV with 5V/1A BEC Output

    Specifications & Features (user manual):http://www.mateksys.com/?portfolio=vtx-hv
    Input voltage: 7~27V(2~6S LiPo)
    40 standard channels, A/B/E/F/R Band
    Output Power: 25, 200, 500mW switchable
    BEC Output: 5V/1A for Camera or FC
    Traditional button+LED control of frequency and power
    BFCMS control via FC UART _TX
    Firmware upgradeable

    Power Consumption: 3.1W Max. @ 500mW
    Video Input Impedance: 75 Ohm
    Audio Subcarrier Frequency: 6.5 MHz
    RF Connector: U.FL (IPEX)
    Video Format: NTSC/PAL
    Weight: 6g (Tx only, w/o SMA cable)
    Size: 36*22*6.5mm w/30.5mm mounting

    Package included:
    1x 5.8G Video transmitter
    1x IPEX to SMA Female, RG178 cable 10cm
    1x IPEX 5.8G whip antenna, RG178 10cm
    1x PVC Heat-shrink tube

  • Matek Systems BetaFlight F405-AIO STM32F405 Flight Controller Built-in PDB 5V/2A & 9V/2A Dual BEC

    Regular Price:

    $39.99
    5 2

    Specifications (User manual): http://www.mateksys.com/?portfolio=f405-aio
    Brand name: Matek Systems
    Item name: BetaFlight F405-AIO
    PCB: 2.3MM, 6 layers & 2oz copper
    Size: 36x51mm PCB with 30.5mm mounting holes & XT60 socket
    Weight: 12g

    FC Specifications:
    MCU: 168MHz STM32F405
    IMU: 32K ICM20602 accelerometer/gyro (SPI)
    Max. 32K Gyro update & 16K PID Loop
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: MicroSD card slot (SD/SDHC)
    VCP, UART1, UART2, UART3, UART4, UART5
    Built in inverter for SBUS input (UART2-RX)
    PPM/UART Shared: UART2-RX
    SoftSerial on S5 & S6 optional
    Smartaudio & Tramp VTX protocol supported
    Spektrum BIND_PIN: RX4
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes

    PDB Specifications:
    Input: 9~27V (3~6S LiPo) w/TVS protection
    PDB: 4x30A (Max.4x50A), 6 layers*2oz copper PCB
    Dual BEC: 5V 2A & 9V 2A
    LDO 3.3V: Max.300mA for Spektrum RX
    Current Sensor 200A (Scale 165)
    Battery Voltage Sensor: 1:10 (Scale 110)

    Features:
    2x LEDs for FC STATUS (Blue, Red)
    6x PWM / DShot outputs without conflict
    5x UARTs
    1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
    4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
    1x pair I2C1 pads (for INAV firmware only)
    1x Side-press button for BOOT(DFU) mode

    package included:
    1x Matek Systems BetaFlight F405-AIO
    1x Rubycon ZLH 35V/470uF (Low ESR)
    4x M3 Anti-vibration Standoffs
    1x FR4 PCB Plate 36*36*1mm

    Out of stock

  • Matek F405-OSD Flight Controller & FCHUB-6S Hub PDB BEC Heli-Nation Exclusive Combo

    Regular Price:

    $39.99
    5 1

    Matek F405-OSD Flight Controller & FCHUB-6S Hub PDB BEC Heli-Nation Exclusive Combo

    Matek Systems F405+OSD BetaFlight STM32F405 Flight Controller Built-in Inverter for SBUS Input

    Specification:
    Brand: Matek Systems
    Item name: Flight Control Board
    Size: 36x36mm
    Mounting hole: 30.5mm
    Weight: 7g
    MCU: 168MHz STM32F405
    IMU: 32K ICM20602 accelerometer/gyro (SPI)
    Support 32K Gyro update & 16K PID Loop
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: MicroSD card slot (SD/SDHC)
    VCP, UART1, UART2, UART3, UART4, UART5
    Built in inverter for SBUS input (UART2-RX)
    PPM/UART Shared: UART2-RX
    Support SoftSerial on S5 & S6
    Battery Voltage Sensor: 1:10
    Currsnt Sensor: No (FCHUB-6S option)
    BEC 5V & 10V: No (FCHUB-6S option)
    LDO 3.3V: Max.300mA for Spektrum RX
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes

    Matek FCHUB-6S Hub Power Distribution Board 5V & 10V BEC Built-in 184A Current Sensor

    Describtion:
    -This PDB distribution power from from a 3-6S Lipo pack to 4 ESCs, as well as providing regulated & filtered DC 5V & DC 10V outputs for powering Cameras, RC receivers, Flight Controllers, Video Transmitters, LEDs, etc.
    - It also has buit-in 184A current sensor and offers a FFC socket to connect the Matek flight controller conviently.

    Specification:
    Brand Name: Matek
    Model: FCHUB-6S
    Item Name: Power Distribution Board Built-in Current Sensor
    Size: 36x36mm
    30.5x30.5mm Hole Mounting , M3
    Weight: 8.5g
    BEC Output: 5V & 10V
    Current Sensor Module

    Out of stock

  • Matek F405-OSD BetaFlight STM32F405 Flight Controller Built-in OSD Inverter for SBUS Input

    Regular Price:

    $29.99
    5 1

    Matek Systems F405+OSD BetaFlight STM32F405 Flight Controller Built-in Inverter for SBUS Input

    Specification:
    Brand: Matek Systems
    Item name: Flight Control Board
    Size: 36x36mm
    Mounting hole: 30.5mm
    Weight: 7g
    MCU: 168MHz STM32F405
    IMU: 32K ICM20602 accelerometer/gyro (SPI)
    Support 32K Gyro update & 16K PID Loop
    OSD: BetaFlight OSD w/ AT7456E chip
    Blackbox: MicroSD card slot (SD/SDHC)
    VCP, UART1, UART2, UART3, UART4, UART5
    Built in inverter for SBUS input (UART2-RX)
    PPM/UART Shared: UART2-RX
    Support SoftSerial on S5 & S6
    Battery Voltage Sensor: 1:10
    Currsnt Sensor: No (FCHUB-6S option)
    BEC 5V & 10V: No (FCHUB-6S option)
    LDO 3.3V: Max.300mA for Spektrum RX
    WS2812 Led Strip : Yes
    Beeper : Yes
    RSSI: Yes

    Firmware based on OpenSource BetaFlight: https://github.com/betaflight

    Features:
    -2x LEDs for FC STATUS (Blue, Red)
    -6x PWM / DShot outputs without conflict
    -5x UARTs
    -1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Sginal/GND
    -4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
    -1x Side-press button for BOOT(DFU) mode
    -1x 16pin bottom mounted FFC Slot for FCHUB-6S connection

    Package included:
    1x flight control board
    1x 0.5mm*16Pin 5cm Flexible Flat Cable
    4x M3 Anti-vibration Standoffs

  • Heli-Nation Matek PDB-XPW 5V 12V Dual BEC PDB Built-in 140A Current Sensor with XT60PW Socket

    Regular Price:

    $9.99

    Matek PDB-XPW 5V 12V Dual BEC PDB Built-in 140A Current Sensor with XT60PW Socket

    The PDB-XPW distributes power from a LiPo pack to 4 ESCs, as well as providing synchronised & regulated DC 5V outputs & linear regulated DC 12V for powering Cameras, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc.It also has built-in 150A current module, and offers a XT60PW socket to connect the LiPo pack conveniently.
    Realacc/Matek PDB-XPW 5V 12V Dual BEC PDB Built-in 140A Current Sensor with XT60PW Socket

    Specification: Manual: http://files.banggood.com/2016/11/PDB_XT60PW_Manual_Realacc(2).pdf

    General:
    -Input voltage range (3S-5S LiPo operation): 9 - 21V DC
    -PDB: 4 x 35A
    -Regulated 5V and 12V outputs
    -Current module 140A
    -LED power indicators ( 5V & 12V outputs )

    Current Module
    - 150A
    -3.3V ADC

    BEC 5V output:
    -Designed for RC Receivers, Flight controllers, OSD, and Servos.
    BEC 12V output:
    -Designed for Video TX or FPV camera with linear regulator.
    BEC 12V @ 3S LiPo
    -Output voltage= 3S LiPo voltage -1V

    Physical:
    -Mounting: 30.5 x 30.5mm, Φ3mm
    -Dimensions: 36 x 50 x 4 mm (w/o XT60PW), 36 x 58 X10.5mm (w/ XT60PW)
    -Weight: 7.0g(w/o XT60PW), 11g(w/ XT60PW)

    Features:
    2oz copper, 4-layers & 2mm PCB. Built-in current sensor 150A
    Built-in XT60PW Socket
    Total 4 pairs ESC solder tabs are fit for X type frame 5V & 12V Output LED indicators & Short circuit tolerant

    Package included:
    1 x Realacc PDB

  • Matek Systems HUBOSD8-SE 9-27V PDB W/ STOSD8-SE 5V&10V Dual BEC For RC Multirotors

    Regular Price:

    $19.99

    Matek Systems HUBOSD8-SE 9-27V PDB W/ STOSD8-SE 5V&10V Dual BEC For RC Multirotors

    Specification:
    Brand: Matek Systems
    Input: 9-27V(3-6s Lipo)
    Input TVS protection
    PDB: 4 X 30A( Max.4x46A)
    BEC 5V 1.5A(2A Max.)
    BEC 10V 1.5A(2A Max.)
    Current Sensor 184A
    Built-in STOSD8-SE
    Size: 46x36x4mm
    Weight: 9g
    Mounting holes: 30.5mmΦ3mm

    -current sensor 184A
    Built-in transient voltage suppressor

    -Serial port
    RSSI(PWM) input
    Current signal output

    -STOSD8-SE
    Autodetect PAL/NTSC
    Dynamic on screen info
    Automatic flight timer
    Auto battery cells defection
    Low battery alarm
    Exceeding mAh alarm
    Min.voltage &Max.current recorder
    Onscreen Pilot ID
    Firmware upgradable
    Simple GUI & setting
    Plug & Play
    BEC power indicators(Red)
    STOSD indicator(Blue)

    Package included:
    1 x PDB
    1 x Rubycon ZLH
    4 x M3x12
    4 x M3x6+6
    8 x M3 nuts

  • Matek FCHUB-6S Hub Power Distribution Board 5V & 10V BEC Built-in 184A Current Sensor

    Regular Price:

    $11.99

    Matek FCHUB-6S Hub Power Distribution Board 5V & 10V BEC Built-in 184A Current Sensor

    Describtion:
    -This PDB distribution power from from a 3-6S Lipo pack to 4 ESCs, as well as providing regulated & filtered DC 5V & DC 10V outputs for powering Cameras, RC receivers, Flight Controllers, Video Transmitters, LEDs, etc.
    - It also has buit-in 184A current sensor and offers a FFC socket to connect the Matek flight controller conviently.

    Specification:
    Brand Name: Matek
    Model: FCHUB-6S
    Item Name: Power Distribution Board Built-in Current Sensor
    Size: 36x36mm
    30.5x30.5mm Hole Mounting , M3
    Weight: 8.5g
    BEC Output: 5V & 10V

    5V BEC Output:
    - Designed for RC Receivers, Flight Controllers, OSD and Servos.
    - DC/DC synchrous buck regulator
    - Voltage: 5.0V (4.9-5.1)DC
    - Current: 1.5A (Max. 2.0A 10S/minute)
    - Short-circuit tolerant ( 2 Seconds/minuate)

    10V BEC Output:
    -Designed for VTX or FPV Camera
    - Voltage: 10.0V (9.8-10.2) DC
    - Current: 1.5A ( Max. 2.0A 10S/minute)
    - Short-circuit tolerant ( 2 Seconds/minuate)
    - 10V can be used to power cameras labeled as 12V.
    - The 3S Lipo input voltage should be 11V plus.

    Current Sensor Module
    - Max. Range: 184A
    - 3.3V ADC
    - Scale the output voltage to milliamps ( 1/10th mW/A): 179


    Features:
    - Total 4 pairs ESC solder tabs are fix for X Type frame
    - Max. 27V input w/ TVS protection
    - Built-in current sensor 184A
    - PDB: 4*30A ( 4*46A, 5 seconds), 4 layers*2oz copper PCB
    - BEC 5V@1.5A ( Max. 2A) w/ 100uf panasonic POSCAP filter
    - BEC 10V@1.5A ( Max. 2A) w/ 47uf TDK MLCC filter
    - 5V&10V output LED indicators & Short circuit tolerant

    Package Included:
    1x FCHUB-6S PDB Board
    1x bag of screws

1 - 16 of 29

Page:
  1. 1
  2. 2