Pyro-Drone HyperLite F4 OSD V2 With VTX Pit Mode Flight Controller

$32.99
Pyro-Drone HyperLite F4 OSD V2 With VTX Pit Mode Flight Controller
 
One of the most popular FC’s is back and better than ever, combining an industry favorite layout with new feature sets for freestyle, long range, and racers. Finally, a board for every pilot!  
 
The new Hyperlite F4 OSD takes the same celebrated ‘flat-bottomed’ layout (crucial for clean and tight builds) and adds a much appreciated OSD and SIX UART ports (more than any other board on the market!) for GPS, RX, SmartAudio, and even Camera Control.  
 
And with more features, comes improved ease of use with a built in 4-in-1 ESC socket and included harnesses for HobbyWing, Airbot, and Spedix 4in1 ESCs. The built in solder pads mirror the 4in1 pad layout, so you can easily connect ANY ESC to this board to get features like current sensing and ESC telemetry (for the BL32 guys). 

Availability: Out of stock

  • DESCRIPTION
  • REVIEWS
  • Version 2 Update:
    The Pyrodrone F4 OSD has a new feature!
    VTX Pit mode compatibilty.

    In order to use this feature jump the two pads with solder on the "PIT" side ( If this feature is not needed then just jump the pads of the "ON" side and your VTX will always be on)
    After you jump the PIT pads connect to Betaflight and go to CLI page , type in the following commands:

    resource PINIO 1 A14
    set pinio_box = 39,0,0,0
    type "save" and then hit enter.

    Wait for the FC to reboot, then go to the "MODES" tab in Betaflight and set VTX PIT MODE to an AUX channel you prefer

    Done! :-)


    Pyro-Drone HyperLite F4 OSD V2 With VTX Pit Mode Flight Controller
     
    One of the most popular FC’s is back and better than ever, combining an industry favorite layout with new feature sets for freestyle, long range, and racers. Finally, a board for every pilot!  
     
    The new Hyperlite F4 OSD takes the same celebrated ‘flat-bottomed’ layout (crucial for clean and tight builds) and adds a much appreciated OSD and SIX UART ports (more than any other board on the market!) for GPS, RX, SmartAudio, and even Camera Control.  
     
    And with more features, comes improved ease of use with a built in 4-in-1 ESC socket and included harnesses for HobbyWing, Airbot, and Spedix 4in1 ESCs. The built in solder pads mirror the 4in1 pad layout, so you can easily connect ANY ESC to this board to get features like current sensing and ESC telemetry (for the BL32 guys). 
     
    PLEASE NOTE: The Hyperlite F4 OSD uses it’s own BF target .bin, “PYRODRONEF4”. 
     
    Tech Specifications:
    MPU6000 Gyro
    STM32F405 CPUE @ 168mhz, can be overclocked
    2-6S direct battery input 
    3.3V 100ma, 5V 1.2A BEC
    5V Camera Power
    Built in configurable Betaflight OSD
    Flat bottom PCB for SUPER CLEAN builds
    36x36 PCB with 30.5x30.5 mounting holes
    6 UARTS. UART1 (INVERTER FOR SBUS),
              UART2 (FREE),
                      UART3 (INVERTED TELEMETRY),
                      UART4 (Free),
                      UART5 (Smart Audio)
                      UART4 (Free)
     
    Built in 4 IN 1 ESC socket(including ESC telemetry, External current sensor)
    Plug and plug with the most popular 4-in-1 ESCs (HobbyWing, Airbot, Spedix, Aikon),with supplied cables
    Built in solder pads mirror of the 4-in-1 ESC socket
    Printed layout instructions ON the board - no need for instructions!