Talon F4 V2 20x20 Flight Controller & Gigawatt V2 4in1 20x20 35A 6S ESC Combo

$81.99
  • Buy 3 for $80.99 each and save 1.2%
  • Buy 5 for $79.99 each and save 2.4%
  • Buy 10 for $78.99 each and save 3.7%
  • Buy 25 for $76.99 each and save 6.1%

Talon F4 is back and better than ever! We managed to add black box and vtx pit switching to the small 20X20 footprint! Pair it up with our Talon Gigawatt V2 4 in 1 ESC for a lightweight powerful 20X20 stack ideal for racing, or to save some weight on your freestyle builds! Fly Talon and be fast as F$@#!


Talon F4 V2 20x20 FC Flight Controller VTX Pit Mode Black Box


Specs

STM32F405 @168mhz

Direct 2-6S input

mpu6000 gyro

Filtered 5V

Built in Betaflight OSD.

4 in 1 ESC socket and direct solder on 4 in 1 ESC pads.

Built in camera control resistor and capacitor

Anchor USB port, for more security and durability

Filtered 5V for camera, vbat battery for VTX.

Current sensor input from 4 IN 1 esc socket and solder pad

Inverter for Sbus (on UART1), (Protocol selectable)

Inverter for smart port telemetry(UART3)

TX4(uart4) near VTX pads for easy smart audio or tramp wiring

TX6(uart6 ) and RX4 ( uart4 )

VTX pit mode switch for 5v and vbat selection

16M blackbox chip

OR
  • DESCRIPTION
  • REVIEWS
  • Talon F4 V2 20x20 FC Flight Controller VTX Pit Mode Black Box


    Specs

    STM32F405 @168mhz 

    Direct 2-6S input

    mpu6000 gyro

    Filtered 5V

    Built in Betaflight OSD.

    4 in 1 ESC socket and direct solder on 4 in 1 ESC pads.

    Built in camera control resistor and capacitor

    Anchor USB port, for more security and durability

    Filtered 5V for camera, vbat battery for VTX.

    Current sensor input from 4 IN 1 esc socket and solder pad

    Inverter for Sbus (on UART1), (Protocol selectable)

    Inverter for smart port telemetry(UART3)

    TX4(uart4) near VTX pads for easy smart audio or tramp wiring

    TX6(uart6 ) and RX4 ( uart4 ) 

    VTX pit mode switch for 5v and vbat selection

    16M blackbox chip


    To use VTX Pit switch please use the custom firmware in the links below. This will be incorporated into the next master release of Betaflight.

    Betaflight 3.5.7 Hex

    Betaflight 4.0.3 Hex

    If you don't want to use VTX Pit switch please enter this code into the cli to keep it always on.  aux 0 39 0 900 2100 0 0



    If you want to use clracingf4 4.0.4 for your Talon F4 V2, please follow these instructions below. On Talon F4 v2. If you want to use the last CLRACING F4 target 4.0.4 Here is the command to make it work Resource flash_cs B12 If you don’t want to use the pit mode switch. Enter this in the cli Resource flash_cs B12 set flash_spi_bus = 2 aux 0 39 0 900 2100 0 0 If you want to use pit mode please go to the tab mode and setup a mode switch for vtx_pit

    WARNING! THIS PINOUT IS FOR TALON F4 V2. IF YOU HAVE A TALON F4 V1 PLEASE CLICK HERE FOR THE PINOUT.







    Note

    The number after the RX and TX indicates what uart those rx and tx line is on, for example.

    RX6 AND TX6, means, rx line and tx line on uart6.

    Sbus pad -> uart1 rx

    Tele-> uart3


    Talon F4 V2 and Gigawatt V2 Pinout