Talon F7 20X20 Flight Controller & Aikon AK32PIN 6S ESC Combo

5 1

Talon F7 20X20 Flight Controller & Aikon AK32PIN 6S ESC Combo

  • A new generation of Talon is here. With a F7 processor and 8S capable, Talon is the only 20X20 on the market with a STM32F722RET6 216MHz processor.  Built in Betaflight OSD, 6 UARTS, and dedicated LDOs for cleaner gyro and OSD signals makes Talon F7 the most powerful 20X20 FC on the market. One of the features Talon F4 users praised is the choice of using the 8 pin harness or direct soldering motor ports to the ESC. We’ve kept that option, while still adding more features, by letting you remove the plastic connector to reveal motor ports.  The 8 pin harness will be a direct pinout for the forth coming Aikon 20X20 6S ESC.

    Main Features

    1. MCU: STM32F722RET6 216MHz
    2. 6-Axis ICM20602 32K
    3. Built in Betaflight OSD
    4. Up to 8S (36V) direct battery power
    5. Buzzer pads for external buzzer
    6. Build in voltage monitoring resistor
    7. 5V 2A BEC
    8. Dedicated LDO for gyro for cleaner gyro signal
    9. Dedicated LDO for OSD for cleaner OSD signal
    10. Led strip shares 5V with 5V/2A BEC
    12. Built in camera control pin with resistor and capacitor
    13. 4 Full UARTS with RX/TX pins
    14. Logical pin layout for cleanest build possible
    15. 8 pin 4 IN 1 ESC plug (Direct solder motor ports underneath)
    16. Remap able LED pad for additional motor output
    17. TX3 & RX3 can be used for I2C for external compass
    18. 5V or 3.3V selectable receiver power
    19. 5V, VBAT selectable VTX and CAM power
    20. Includes * pin connector (Aikon compatible), 8 grommets, M3 to M2 nut adapters, M3X5 standoffs

    Betaflight Target: CLRACINGF7

    WARNING! RX2 is labeled Ground on the flight controller silkscreen. This IS NOT a ground. Please refer to pictures for Ground and RX2. 

    Top View

    Bottom View

    The 6S 20X20 ESC we've been waiting for is here! Following the success of the AK32 30X30 6S 4 in 1, Aikon has crammed the same tech into a 20X20 format. Pair this ESC with our Talon F7 FC for an ultralight plug and play 6S stack!

    The Aikon AK32 35A 4IN1 BLHeli32 comes with STM32F051 micro processor with latest BLHeli_32 firmware. It supports 6s input, comes with current sensor to monitor the current output. 

    What makes the AK32 different?

    • New BLHeli_32 code base
    • Programmable PWM frequency of up to 48KHz
    • Auto-timing for higher efficiency and reliability
    • Voltage/Current limiting
    • Adjustable “Brake on Stop” force
    • Improve direction change in Bidirectional mode
    • ESC Telemetry
    • Configuring from FC using DShot commands


    Battery: 2-6s
    Constant Current: 35A
    Burst Current: 45A
    Size: 36*36mm
    Firmware: BLHeli32
    MCU: STM32 F051
    Bootloader: Yes
    Weight( with/wire): 16g
    Signal wire length: 100mm
    Battery wire length: 100mm


    WARNING! If you remove the JST connector to direct solder, the pinout is not the same as the JST connector. Please use the diagram below to see the correct pinout. Pay attention to VBAT and Ground!