Talon GigaFusion Fusion F7 & Gigawatt V2 6S 35A ESC Combo

4.9 3
$91.33

3 Review(s) | Add Your Review

Talon GigaFusion Fusion F7 & Gigawatt V2 6S 35A ESC Combo
OR
  • DESCRIPTION
  • REVIEWS

  • Our flagship Flight Controller is here and WOW! Using a dual gyro setup in 90° phase and a F7 processor will have your quad dialed in to the max! Pair it with our Talon Gigawatt 6S 35A ESC and you have a 20X20 6S powerhouse!


    For Betaflight 4.2 or later, youll need to enter this into CLI 

    resource pinio 1 A14,

    set pinio_box = 40

    Save



    Specs

    1. MCU: STM32F722RET6 216MHz
    2. 2x ICM20602 GYROS 90 deg phase
    3. Built in Betaflight OSD
    4. Up to 8S (36V) direct battery power
    5. Buzzer pads for external buzzer
    6. Built in voltage monitoring resistor
    7. 5V 2A BEC
    8. Dedicated LDO for Gyro, noise free gyro power
    9. Dedicated LDO for OSD, cleaner OSD signal
    10. Led strip shares 5V with 5V/2A BEC
    11. 6 UARTS: UART1, UART2, UART3, UART4, UART5, UART6
    12. Built in camera control pin with resistor and capacitor
    13. 5 Full UARTS with RX AND TX pins
    14. Logical pin layout for cleanest build possible
    15. 8 pin 4 IN 1 ESC plug
    16. Remapable LED pad for additional motor output
    17. TX3, RX3 can be used for I2C for external compass
    18. 5V, VBAT selectable VTX and CAM power
    19. 16M Blackbox flash chip
    20. No flicker VTX pit mode switch (positive switch)
    21. M4 Can be selected either led_strip signal or M4 signal for RPM filtering

    20 X 20 mounting hole with true 25mm board dimensions

    Official Betaflight Target: TalonF7Fusion

    Please use user1 for Pit Switch Mode Switch 


    For the Legacy Clracingf7 target you will need to do the following:

    To get Motor 4 to work please use the CLI command below using Betaflight V4.0.4. A custom hex is coming soon for 4.0.4.

    Resource MOTOR 6

     None

    Resource MOTOR 4 C08

    Save


    To get 5V to your VTX please go to the mode tab in Betaflight and setup a mode switch for vtx_pit


    Setting up Pit Mode:




    TOP LAYOUT


    BOTTOM LAYOUT

    Looking for the perfect 6S companion for your Talon FC? Good news! The Talon Gigawatt V2 has arrived! 

    The Talon Gigawatt V2 4-in-1 35A 6S is a new generation ESC that uses a variety of bleeding edge technologies in hardware and firmware.
    The Talon Gigawatt is worth your investment.
    BLHeli_32 code base
    Programmable PWM frequency of up to 48KHz
    Auto-timing for higher efficiency and reliability
    Analog Voltage/Current sensing
    Adjustable “Brake on Stop” force
    Improve direction change in Bidirectional mode
    One current sensor to measure the total amp draw and telemetry functions.
    ESC Telemetry (Voltage and RPMs and current)
    Configuring from FC using DShot commands
    Programmable sine modulation mode
    Programmable soft bidirectional mode
    Programmable autonomous periodic (every 32ms) telemetry mode
    Hardware noise filter on the signal input
    New Aluminum Heat shield to help dissipate heat



    SPECIFICATIONS
    Battery2-6s
    Constant Current35A
    Burst Current45A
    Mount Hole20*20mm
    FirmwareBLHeli32
    MCUSTM32PINF0
    BootloaderYes
    Weight( with/wire)10g
    Signal wire length100mm
    Battery wire length100m