TomoQuads Whoopee HD V2 Cinematic Quad Frame For Beta75 Pro 2 & Mobula7

$22.95
OR
  • DESCRIPTION
  • REVIEWS
  • WHOOP THERE IT IS!

    YOUR CINEMATIC HD WHOOP FRAME KIT


     
     

    Features:


    3K Carbon Fiber frame


    No Prop view


    Supports Beta75 Pro 2 & Mobula7 frame guards (not included, purchase separatly)


    Uses knurled aluminum standoffs


    Top or bottom mounted lipo battery


    Tpu camera mount to reduce vibration


    Support  16x16 , 20x20 or the diagonally mounted beta75x or mobula stack 


    25mm stack height to fit most of your components with ease 


    CF are cut along the weave.


    6g. CF  only 10g. with hardware


     
     

    Specification:


    1mm 3K carbon fiber bottom plate


    1mm 3K carbon fiber top plate


    Size: 92mm MTM 


    Knurled black aluminum 25mm m2 standoffs


    Flexible TPU 3D printed parts


    Supported FC stack bottom plate : 16x16 , 20x20, 36x36 (needs m2 5mm+- standoffs not included)


    Top plate have a 20x20 hole pattern for mounting the Runcam split mini2  or Caddx Turtle


    Motor hole dimension: 9mm  


     

    Included in the kit:


    1pc. CF bottom plate


    1pc. CF top plate


    3pc. 25mm M2 Knurled aluminum standoffs and screws


    3D printed camera mount


    3D Printed antenna mount


    3D printed battery strap


    Prop guards are not included and must be purchased seperatly see link below.


     

    Recommended parts:


    (Tested)


    HGLRC Zeus AIO 20x20 stack or 16x16 stack eg: Super S AIO 


    1103 10,000KV motors or higher 


    40mm Beta75x 4bladed props or similar


    Runcam Split Mini 2 or Caddx Turtle 


    Runcam TX20U VTX or similar


    Any micro receiver RX or your choice


    300~450mah 2S lipo battery


    Select Rakon Kit Style1 or Style2 if you are to use  the Rakon Heli 40mm Prop guards for 1103 motors. 


    Support for 0802  motors from Beta Pro2 /Mobula7



    Build Notes:


    -Remember that this is not a direct conversion kit for your Beta75x. This frame supports 20x20, 16x16  and 36x36  so you can use a wide variety of stack , use the one you think that would  work best for your build. The recommended build is just a guidline. 


    -Following the recommended build will saves you a lot of headache avoiding  the hassle of sourcing for parts thats can be hard to find.


    -Keep your build as light as possible by using lighter components .Proper cable management is also very important to save on weight.


    -If you are using a 16x16 or whoop fc stack you will need to mount the 20x20 Runcam Split Mini2 or Caddx Turtle on the top plate unless you are building a straight 20x20 stack


    -For Beta75x  prop guards/frame,  you will need to cut them in to 2 or 4  parts using a simple wire cutter (see pic). Make sure you select the Beta75 Kit  on checkout.


    -The Beta75x frame/guards have a smaller M1.6 holes vs M2 on the 1103 motors, slightly widening the holes on the plastic  guards will makes motor mounting a breeze.  This only applies to the Beta75x guards and not the Rakon guards.


    M7 / Pro2 version : If you are going to use  0802 motors and M7 /Pro2 frame guards and includes M1.4 motor screws


    Note: Pictures shown are for illustration purposes only and some are not  included with the kit, see product description for details. 


     

    Any Videos?